Many people wonder what the difference between radiant and infrared heat is, but both heating sources are from an infrared radiant energy source. The principles of radiant and infrared are similar but the difference really lies in the temperature. The shorter the electromagnetic wave length the higher the heat source. If you are looking for an industrial radiant heater that are quick to reach operating temperatures and maintain comfort please consider Indeeco radiant heating equipment.
For more information and product details, visit www. Heater not passing maintenance turnarounds? Use these steps — the same procedures heating suppliers use — to evaluate your equipment. A final advantage is simply comfort. By heating your floorboards, radiant heating can reduce that horrible feeling of walking on cold tile or wood floors during the winter. Due to some of the costs associated with tearing up floors, hydronic radiant heating is typically installed at the time the house is constructed or being remodeled.
Many older homes here in Buffalo have radiant heating systems that utilized copper pipes, but some newer ones are getting retrofitted with radiant heating. Once operating, hydronic heating holds its temperature better, requiring less energy from the boiler to retain heat. Electric systems constantly drain power, driving your costs up. Though cheaper to install, electric floor heating costs much more to run, especially in large areas.
To find out more about how radiant heating works, or to get a free in-home estimate for adding radiant heat to your Buffalo home, give us a call!
Close Menu. They also require reflective insulation under the tubes to direct the heat upward. Your boiler or water heater is linked to a manifold -- a system of separate pipes that channel water from a single source into different zones. This way, you can heat each area of your home separately from a single programmable thermostat.
From the manifold, the hot water is sent through a pattern of PEX tubing by a re-circulating water pump. PEX is polyethylene tubing that's leak-free, non-toxic, flexible and capable of handling high temperatures. Maintenance for a hydronic system is minimal -- the boiler needs an annual check-up, but most modern pumps use water to lubricate the parts and are low-maintenance.
However, if your system breaks, you'll need to hire a professional, because fixing it can be complicated. It's also expensive. In some cases a unit is beyond repair and must be replaced, which costs about the same as a first-time installation. There are lots of variables, but the good news is your RFH specialist can walk you through the different options. Electric radiant floor heating RFH uses heat-conducting plastic mats containing coils warmed by electricity.
So what are these heating coils? They aren't heated elements like you'd find in a space heater or on an electric stove. They're actually resistance wires, typically copper or nichrome, wrapped in a water -resistant polymer.
Nichrome is an alloy of nickel and chromium with high electrical resistance -- ideal for producing heat. These wires are zigzagged through a mat and then wired for electricity. Think of a large, rolled-up electric blanket without the fabric and you'll get the picture. On installation day, you or your contractor will roll out the mats and put the flooring material in place. Most people choose to go with electric RFH just for individual rooms since the cost of electricity makes this system quite expensive for heating an entire house.
You can save money if your local power company charges less for off-peak usage. Cheaper nighttime power rates allow consumers to charge the heating elements overnight for less money -- then the heat is used over the course of the following day. Electric RHF works best with floors made of ceramic tile, but it can be used with most types of flooring, including hardwood floors.
Carpet is thicker and doesn't conduct heat as well as tile or hardwood flooring, but selecting the correct padding can greatly increase the amount of heat you'll get. There are two kinds of padding used on carpets -- slab and ribbed. Slab pads are flat and ribbed and have a waffle pattern. Because an electric RFH system is usually used for single rooms, it's controlled either with a simple flick of a switch or automatically by thermostat.
Since electric RFH system heating coils are installed between the subfloor and the floor covering itself, heating time is short. This blog post discusses the advantages and disadvantages of radiant floor heating. We will start with the pros and move after that to the cons. Find out more about Floor Heating.
Energy Efficient Heating There are two types of radiant floor heating , electric and water-based systems. Radiators — The Key Differences. View Warmup Thermostat Range. Works with all floor coverings Underfloor heating gives you the freedom to design your home as you wish, making the most of all the wall and floor space. Learn more about Floor Coverings 5. Safety and Comfort When you have underfloor heating, you no longer need to worry about sharp edges or hot surfaces of radiators when younger family members are in the house.
Ease of Installation Underfloor heating is easy to install, especially if you make it part of a build or renovation project. Cons of Radiant Floor Heating 1. Installation Time As you usually need to apply a self-leveling compound on top of the electric underfloor heating system, you should factor in the time it takes for this to completely dry before the floor covering can be put in place — this is usually a day or two. Heated Floors Floor heating is the modern heating solution — creating the perfect temperature, making you feel warm and comfortable from the moment you enter the room.
Recommended for you:.
0コメント